Skip to content
Speaker Tester

Device · Earbuds

Earbuds Test

In-ear buds live or die by their fit. This sequence checks that each bud plays on the right side, that both are equally loud, whether the tips seal well enough for proper bass, and how far your treble reaches.

  • Free
  • No download
  • No sign-up
  • Audio stays on your device

Loading…

7 steps · about 45 seconds

Press play to run every test

Each bud, center, polarity, seal, treble range and fit, one after another.

  1. 1Left bud4 s · Only the left ear. If it plays in the right, the buds are swapped.
  2. 2Right bud4 s · Only the right ear.
  3. 3Center4 s · Inside the middle of your head. If it leans to one side, one bud is louder or sits less deeply.
  4. 4Out of phase4 s · Strange, spread out, “outside your head”. That’s correct for this step.
  5. 5Seal check 20–200 Hz12 s · Bass should be clearly audible from ~40 Hz. Weak bass almost always means a poor seal: try the next tip size.
  6. 6Treble sweep 20–4 kHz12 s · A falling high tone. Note when you first hear it in each ear.
  7. 7Pink noise5 s · Even hiss in both ears. Push each bud in slightly. If the sound changes a lot, the fit isn’t sealing.
20%

Start quiet. Lower your device volume before you press play, then raise it slowly. Test tones are pure and can be louder than music at the same setting.

The seal check: why fit matters more than the earbud

Earbuds create bass by pressurising the small volume of air sealed in your ear canal. If the tip leaves a gap, that pressure leaks out and the low end disappears, so the same earbud can sound thin in one ear and full in the other. On the 20–200 Hz seal step, bass should be clearly audible from around 40 Hz. If it only appears above 80–100 Hz, or one ear sounds much weaker, try the next size of ear tip. Many people need a different size in each ear.

Foam tips seal more reliably than silicone for many ears. Apple and Samsung both include an ear tip fit test in their apps, which uses the microphones; this test is the manual version and also works for any wired or wireless in-ear model.

Balance, polarity and treble problems

If the center step leans to one side, one bud is either sitting less deeply or is partly blocked by earwax. Clean the nozzle mesh gently with a dry soft brush, never liquids, and test again. A persistent imbalance with good fit can also come from accessibility settings: check the left/right balance slider and make sure mono audio is off.

The out-of-phase step should sound strange and spread out, as if it is outside your head. That’s correct. On the treble sweep, note when you first hear the falling tone in each ear; the two should match. A big difference between ears with clean buds is worth mentioning to a hearing professional, since earbuds can’t explain it.

Frequently asked questions

How do I test if my earbuds fit properly?

Run the seal check step. With a good seal, bass is clearly audible from about 40 Hz. If it is weak or uneven between ears, try a different tip size or foam tips.

Why is one of my earbuds quieter?

Usually earwax on the nozzle mesh, a poorer fit on that side, or a balance setting. Clean the mesh with a dry brush, reseat the bud, and check the balance and mono audio settings.

Should I turn off noise cancelling for this test?

Yes for the first run, so you hear the buds without processing. Then repeat with noise cancelling on to check it doesn’t add hiss or change the balance.

Can I use this test for AirPods?

Yes. It works with AirPods, Galaxy Buds, Pixel Buds and any wired or wireless in-ear. Turn off spatial audio and head tracking so the channels stay fixed.

Keep testing

See All Tests

Want to check everything in one go? Run the full speaker test on the homepage.