Skip to content
Speaker Tester

Web Audio · 100% in your browser

Online speaker test, right in your browser

Run a free speaker test in seconds: check left and right channels, phase, bass, subwoofer and frequency range on speakers, headphones and phones. No download, no sign-up, and no audio ever leaves your device.

Test everything

One click. Eight checks. Under a minute.

The full sequence plays each test automatically and tells you what you should hear. Flag anything that sounds wrong and you’ll get a direct link to the detailed test that fixes it.

  • Left · Center · Right
  • In phase vs. out of phase
  • Bass sweep 20–200 Hz
  • Full sweep 20 Hz–20 kHz
  • Pink noise

Using headphones? Try the headphone test, which uses the same sequence tuned for earcups and earbuds.

Loading…

8 steps · about 57 seconds

Press play to run every test

Left, center, right, phase, bass, frequency range and noise, one after another.

  1. 1Left channel4 s · Sound only from the left speaker or ear.
  2. 2Center4 s · Sound from both sides, appearing in the middle.
  3. 3Right channel4 s · Sound only from the right speaker or ear.
  4. 4In phase4 s · Focused, centered and full. Remember how this sounds.
  5. 5Out of phase4 s · Wider, vaguer and thinner than the last step. If it sounds fuller, your wiring is reversed.
  6. 6Bass sweep 20–200 Hz12 s · A rising low tone. Listen for buzzing or rattling, and note when it becomes audible.
  7. 7Full sweep 20 Hz–20 kHz20 s · A smooth rising tone with no gaps, jumps or distortion until it fades out at the top.
  8. 8Pink noise5 s · A smooth, even hiss with no crackle, popping or one side louder than the other.
20%

Start quiet. Lower your device volume before you press play, then raise it slowly. Test tones are pure and can be louder than music at the same setting.

All tests

Pick a test

Each test has its own page with detailed controls, step-by-step instructions and answers to common questions.

Test tones

Play a single frequency

28 test tones from 20 Hz to 20 kHz, each with waveform and channel controls and a guide to what it reveals.

Open Tone Generator

Why Speaker Tester

A modern test bench, not a folder of audio files

Generated live, not recorded

Every tone, sweep and noise is synthesised in real time. Pick any frequency to the hertz, with no MP3 artifacts and nothing to download.

See what you hear

Live frequency readout, a left/right oscilloscope and speaker indicators show exactly what’s playing, so you don’t have to wait for a voice-over.

Safe by default

Every test starts at 20% volume with fade-ins, a high-volume warning and a built-in limiter to protect ears and tweeters.

Keyboard first

Space to play or stop, arrows for channel and frequency, M to mark cut-off points. Every control is reachable without a mouse.

Private by design

No sign-up, no microphone, no cookies, no uploads. Once the page loads, the tests even work offline.

Built for phones too

Large touch targets, responsive layouts and the same features on a 5-inch phone as on a 27-inch monitor.

How it compares to traditional test-tone sites

FeatureSpeaker TesterTypical test-file sites
Sound sourceGenerated live, any frequencyFixed pre-recorded files
Frequency readoutLive on screen, to the hertzVoice-over every few seconds
Find your cut-offMark button with range summaryListen and remember
Channel & phase visualsSpeaker indicators + L/R scopeText labels
Volume safetyStarts at 20%, warning, limiterPlays at file level
Keyboard shortcutsSpace, arrows, M, S, FNone
Run everything at onceGuided sequence with flagsOne file at a time
PriceFree, no paywalled featuresDownloads and options behind donations

Speaker test guide

What a speaker test checks, and why it matters

A speaker test plays known signals so you can compare what you hear with what you should hear. Busy music hides problems; a pure tone, a sweep or steady noise doesn’t, so a missing channel, a rattling cone or a dead tweeter stands out within seconds.

A complete speaker check covers four things: channel routing (is left really left?), polarity (are both speakers pushing in the same direction?), frequency range (how low and high it can play) and clean output (no buzz, crackle or distortion). Run one after setting up new speakers, swapping cables or updating audio drivers, and whenever something sounds off.

How to test your speakers step by step

  1. Turn your device volume down to about a quarter, close other apps that play sound, and sit where you normally listen.
  2. Press play on Test Everything above. During the left and right steps, say which side you hear before you look at the screen.
  3. Listen to the phase comparison. In phase should sound solid and centred; out of phase should sound wide, hollow and thin in the bass.
  4. During the sweeps, note where sound fades in at the bottom and where it disappears at the top. Flag any step that buzzes, crackles or sounds wrong.
  5. Open the linked test for anything you flagged, change one thing at a time, then test again.

What your speaker test results mean

No sound on one side

Check the balance slider in your sound settings, then the cable on the silent side. If the silence follows the cable when you swap leads, replace the cable; if not, check the speaker or amplifier channel. The left right speaker test plays each side on its own.

Distortion, buzzing or rattling

If the noise disappears when you lower the volume, the speaker was just overdriven. If it stays, look for a loose grille, something touching the cabinet or a torn cone. A slow frequency sweep is the quickest way to find the exact note that rattles.

Weak or missing bass

Small speakers fade out below about 80–100 Hz, so a thin low end on a laptop is normal. On a full system, weak bass usually means reversed polarity, a subwoofer that is off or set too low, or a crossover gap. The bass test shows exactly where the low end stops.

Reversed polarity

If the out-of-phase step sounds fuller than the in-phase one, one speaker is wired backwards. Swap the red and black wires on one speaker only, then confirm the fix with the phase test.

Speakers, headphones and phones: what changes

The same stereo sound test works on any output, but what counts as normal is different for each.

Room speakers

The room shapes the sound: bass can boom in one seat and vanish in another, so always test from your usual listening position.

Headphones and earbuds

Each ear hears only one driver, so channel and polarity faults are obvious, but bass depends heavily on fit and seal. The headphone test runs the same sequence tuned for earcups and earbuds.

Phones and laptops

Many phones pair a bottom speaker with the earpiece, so stereo only works in landscape, and some models play mono. For an iPhone speaker test, turn off silent mode and remove the case if sound seems muffled. The phone speaker test explains what is normal for small built-in speakers.

Keep the volume safe

Test tones are pure and continuous, so they can sound louder than music at the same setting. Start low and raise the level until the tone is clear, never painful. Treat high frequencies and sub-bass with extra care: a loud sweep can damage a tweeter or a small driver in seconds.

With headphones, stay well below the level you use for music, and take a break if your ears ring or feel blocked. Hearing damage builds up over time and does not heal.

Frequently asked questions

How do I test my speaker sound online?

Press play on the Test Everything player at the top of this page and listen as each step plays. In under a minute it checks the left, center and right channels, compares in-phase and out-of-phase sound, sweeps the bass and the full 20 Hz–20 kHz range, and plays pink noise. Flag any step that sounds wrong, then open the matching test, such as the left/right test or the frequency sweep, for a closer look.

What is the best app to test speakers?

You don’t need an app: a browser-based speaker test like this one runs on phones, tablets and computers without installing anything. Open the page in Safari, Chrome, Firefox or Edge and every tone is generated live on your device, so it works the same on iPhone, Android, Windows and Mac. Your operating system also has a basic built-in sound test, but it only confirms that sound comes out. It can’t check channels, phase or frequency range.

How do I test my speakers on Windows or Mac?

Both systems have a basic built-in check, and a browser test covers what they miss. On Windows, open Control Panel > Sound, select your speakers on the Playback tab, click Configure and press Test to hear each channel in turn. On a Mac, open System Settings > Sound, choose your speakers under Output and move the Balance slider while audio plays. To check phase, bass and the full frequency range too, run the Test Everything player on this page in any browser.

Is Speaker Tester really free and private?

Yes. There’s no account, no paywall and no download. Every sound is generated live in your browser with the Web Audio API, and nothing is recorded or sent anywhere. The microphone is never used.

Do I need to download any test files?

No. Instead of playing pre-recorded MP3s, Speaker Tester synthesises each tone, sweep and noise in real time. That means any frequency is available instantly, with no compression artifacts and no waiting for files to load.

Will it work on my phone?

Yes. It works in current versions of Safari, Chrome, Firefox and Edge on iPhone, Android, Mac, Windows, Linux and Chromebook. On iPhone, make sure the silent switch is off, because Web Audio follows it.

Why is my speaker not working?

A silent speaker is usually a settings or connection problem rather than a broken speaker. Check that the right output device is selected, the volume isn’t muted, Bluetooth isn’t connected to another device and every cable is pushed fully in, then restart both the device and the speaker. If only one side is silent or the sound is distorted, run the left/right test and the frequency sweep to find out whether the cable, amplifier or speaker is at fault.

Can test tones damage my speakers or hearing?

Yes, at high volume, but at moderate levels they are safe for both. Loud, steady tones can overheat tweeters, push small woofers past their limits and harm your hearing. Every test here starts at 20% volume, warns you above 70% and runs through a safety limiter. Still, lower your device volume before pressing play and raise it slowly. Don’t hold loud high tones or deep sub-bass for long, and stop as soon as you hear rattling, popping or harsh distortion.

Does the speaker test work with Bluetooth speakers and wireless headphones?

Yes. It works with anything your device plays sound through, including Bluetooth speakers, AirPods and other wireless earbuds. Expect a short delay before each sound, because Bluetooth adds latency. If the top of the sweep cuts off early, the connection may have dropped into a low-quality call mode: close any app using the microphone and reconnect.

Why can’t I hear the highest tones in the sweep?

Usually that’s your ears, not your speakers. Most adults stop hearing somewhere between 14 and 17 kHz, and the limit drops with age and noise exposure. To tell the difference, run the same sweep on a second device or pair of headphones. If the cut-off is the same on both, it’s your hearing.

Why do I hear sound from both sides during the left or right step?

Something is mixing the channels to mono. Look for a mono audio switch in your device’s accessibility settings or a stereo widening or virtual surround effect, and remember that many Bluetooth speakers and some phones have only one speaker. Soundbars can also spread a single channel across the whole bar.

Can a speaker test fix a blown or water-damaged speaker?

A test shows you what’s wrong, but it can’t repair a torn cone or a burnt voice coil. If water got into a phone speaker, the Speaker Cleaner plays a low 165 Hz tone that can push droplets out of the grille. A blown speaker usually needs to be repaired or replaced.

Hear what your speakers can really do.